RLC CAN-X

LIGHTING CONTROLLER

More Guides

Product Overview

AVAILABLE FEATURES

Rotary Dimming Control

Rotary Dimming Control

Hazard Warning Flash

Turn Signal Flash Pattern

High/Low Beam Sync

Daytime Running Light Mode

Multi-Group Light Control

Horn Strobe Sync

RaysDim Lighting Controller RLC-CAN

Seamless OEM Integration. Plug-and-play installation with native motorcycle button control. No additional switch installation required. Control your auxiliary lights intuitively during rides. 

 

KEY FEATURES: 

Four Independent Circuits 

Control up to four auxiliary light groups independently through OEM buttons. Each group can be activated individually or in combination, creating multiple lighting configurations to enhance visibility and riding safety. 

 

Smart Memory Function 

The controller remembers your last light configuration and automatically restores it on the next startup. For example, if you power off with Light Group l on and Light Group 2 off, those exact settings will be restored when you power on again-ensuring consistent control state and improving ride-time convenience.

Product Overview

PACKAGE CONTENTS

① RLC-CAN Controller ×1 

② XT60 Power Input Cable × 1

Wiring Harness Installation

2.1 System Overview & Connection Guide

 The CAN bus connector adapter cable is an optional accessory and must be purchased separately based on your motorcycle model. 

 

2.2 Main Connection Points 

① CAN Bus Interface 

Connect the CAN bus connector adapter cable to the vehicle's OEM CAN bus system. Selection is model-dependent; verify compatibility before purchasing. 

 

② Upgrade Serial Port 

Reserved for firmware updates and advanced system configuration (administrator use only). Not required for standard operation.

资源 1

CAN Bus Interface

Connect the CAN bus connector adapter cable to the vehicle's OEM CAN bus system. Selection is model-dependent; verify compatibility before purchasing.

资源 2

Upgrade Serial Port 
Reserved for firmware updates and advanced system configuration (administrator use only). Not required for standard operation.
Title

Auxiliary Light Output Connectors 
The controller supports connection to up to four auxiliary light circuits, organized as Light Group 1 and Light Group 2, with each group subdivided into right (R) and left (L) channels.

 

Key Points: 
① Each output connector is labeled for easy identification. (e.g., "L1" for Light Group 1 Left, "R2" for Light Group 2 Right)


② RLC CAN-X enables independent control of up to two pairs of auxiliary lights.


③ Each light group can be controlled individually or in combination.


④ Ensure all auxiliary light extension cables are fully inserted and locked to guarantee waterproof integrity.
Title

4PIN (RDC Connector) 
Applicable models 

R1200GS/A 

R1250GS/A 

R1200R 

R1200RT 

Your custom text goes here

6PIN (DWA Connector) 
Applicable models 

1300GS/A

8PIN (RDC Connector) 
Applicable models 

K1600

F750/F850/F900 

R18

S1000XR 

C400X/GT

Installation Procedure

Step 1: Locate the OEM CAN Bus Interface

・The original motorcycle CAN bus interfaceis located in a concealed area beneath the seat. 
・Look for the connection point on the seat base or frame, typically featuring a 2-pin or 3-pin connector. 
・Consult your motorcycle's service manual if uncertain about the exact location. 

Step 2: Remove Protective Cap and Connect Adapter Cable 
・Carefully remove the protective cap from the OEM CAN bus interface 
・Insert the appropriate CAN bus connector adapter cable into the OEM interface (ensure full seating and secure connection) 
・Verify the connector type matches your motorcycle model

Step 3: Connect Adapter Cable to RLC-CAN Controller
・Locate the CAN bus input port on the RLC-CAN controller
Insert the JST 2-pin connector from the adapter cable into the controller's .
Title

(DWA Module Example)

(RDC Module Example)

Watch the Q5 Pro + RLC CAN-X Complete Installation Guide

Alt image

Lighting Control

①Rotary Dimming Control 

Left Tilt (Hold 1 second) → Activate Light Group 1 Dimming. 

Right Tilt (Hold 1 second)→ Activate Light Group 2 Dimming After lights flash, enter dimming mode. Adjust brightness within 5 seconds; auto-exit after 5 seconds. 
 

② Cruise Strobe Mode 

Press the high-beam button five times within 5 seconds to activate continuous strobe mode. Press the high-beam button once more to exit. 

 

③ Hazard Flash Sync 

Auxiliary lights synchronize with motorcycle high-beam: 

High-beam ON→Auxiliary lights high brightness 

Low-beam ON→Auxiliary lights low brightness. 
 

④ High-Beam Sync 

・Auxiliary lights synchronize with OEM high-beam activation- When high-beam is engaged. 

・Auxiliary lights turn on- When high-beam is disengaged→Auxiliary lights turn off.
 

⑤ Turn Signal Light Control 

Light Group 1: Hold 1 Second→Toggle Light Group 1On/Off 

Light Group 2: Press 3x Quickly→Toggle Light Group 2 On/Off.
 

⑥ Horn Strobe Activation 

Long Press: Activate Light Strobe Mode(Lights flash while horn is pressed) 

Short Press: Horn Sounds Only (No Light Strobe).

Watch how it works

Alt image

Important Precautions

Function Check: 
Before installation, power on the device and verify all functions operate normally. 
 

Standard Operating Procedures: 
Operate the product only within the specified parameters to prevent damage or safety hazards. 
 

Proper Installation Location: 

Mount the controller in a well-ventilated area. Avoid covering the controller or placing it near high-temperature heat sources such as exhaust pipes, engine, or radiator. 
 

Fuse Replacement: 

If the fuse blows, identify and resolve the underlying cause first, then replace with a fuse of the same specifications. 
 

Protect Wiring: 

During installation, avoid damaging the wiring harness.Damaged wiring compromises waterproof integrity and reduces product lifespan.Use soft cable ties for securing. 
 

Product Compatibility: 

This product is designed exclusively for Q5Ppro auxiliary lighting systems. Do not use with incompatible third-party equipment.
 

Professional Installation: 

Ensure installation and maintenance are performed by qualified technicians. assumes no responsibility for damage caused by improper installation or maintenance.

Troubleshooting Guide

If the wiring harness or auxiliary lights exhibit problems, follow the steps below to quickly identify the faulty component.

Step 1: Check Wiring Connections 
Verify that all power and CAN bus connectors are properly connected and seated.Check that all extension cable connectors are fully locked into position. 


Step 2: Replace Components Sequentially 
Systematically replace components one at a time to isolate the faulty part: auxiliary lights, controller, extension cables, power cable, and other components. 


Step 3: Swap Left and Right Lights 
Swap the left and right auxiliary light cables and the extension cable connectorsconnected to the controller to determine the fault location.

Step 4: Common Problems & Solutions 
One Side Works, Other Side Does Not 
・Check if the non-functioning side's extension cable connector is fully locked 
・Disconnect and reconnect the cable to ensure proper contact 
・Swap left and right cables to isolate the faulty cable or controller port 
Light(s) Won't Turn On 
・Verify dimming mode is not active (hold knob for 1 second to activate light) 
・Check if turn signal light requires correct button sequence 
・Test power supply voltage and fuse status 
Lights Flickering or Unstable 
・Measure voltage at controller input (should be 12-15V DC stable) 
・Check all power connections are clean and tight 
・Verify power supply is sufficient and stable 
CAN Bus Connection Not Recognized 
・Check for corrosion or moisture on connector pins 
・Confirm the CAN adapter cable type matches your motorcycle model 
・Verify the adapter cable is fully inserted into the OEM CAN interface

Motorcycle Spotlight & Accessories